< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=1094061016523056&ev=PageView&noscript=1" /> All-In-One Solar ESS ES Standard:3.6kW+7.68kWh - piforz.com
EN

All-In-One Solar ESS ES Standard:3.6kW+7.68kWh

This product is suitable for 25.6V product applications and
can be used in conjunction with photovoltaics and inverters
to supply power to household televisions, air conditioners,
lighting fixtures, etc. This product has voltage, current, and
temperature protection functions.

Testing Condition

Unless otherwise specified in the testing project, all tests in this specification shall be conducted under the following conditions:
Environmental temperature: 25 ± 2 ℃;
Relative humidity: 65% ± 20%

Test Instrumentation & Device Characteristics

The accuracy of the voltage measuring instrument should not be lower than level 0.5, and the internal resistance should not be less than 10k Ω/V; The accuracy of the current measuring instrument should not be lower than level 0.5; The accuracy of the instrument used for measuring time shall not be less than ± 0.1%; The temperature measuring instrument should not be lower than ± 1 ℃; The voltage output and detection accuracy of the battery charge and discharge tester shall not be less than ± 0.5%; The current output and detection accuracy shall not be less than ± 0.1%;

Safety Performance Requirements

Item Test Method Require
Short Circuit After being fully charged using the standard charging method at 25 °C, short-circuit the positive and negative terminals of the battery pack’s discharge port with wires (wire resistance 80 ± 20m Ω) for 1 hour. The battery pack should not leak, ignite, or explode.
OverCharge After charging with the standard charging method at 25 °C, set the constant current source to 1.25 times the nominal voltage and 0.1I (A).
Discharge Discharge the battery pack to the termination voltage or battery pack protection, and then continue discharging for 5 hours at 0.1I (A). Visually inspect the appearance and ensure that there is no leakage, smoke, fire, or explosion.
Constant Damp Heat Test After charging using the standard charging method at 25 °C, place it in a constant temperature and humidity chamber at (40 ± 2) °C and relative humidity of 90-95% for 48 hours; After 7 hours of storage, visually inspect.
High and low temperature impact After charging using the standard charging method at 25 °C, place the battery pack in an environment with a temperature of 75 °C± 2 °C for 6 hours, then move it to an environment with a temperature of -40 °C for 6 hours. The time interval between moving from the highest temperature to the lowest temperature should not exceed 3 minutes. Repeat the above steps, after 10 cycles, remove and let it sit for 24 hours, and visually inspect.

Parameters

Inverter Parameters INV 3600
Power 3.6KVA / 3.6KW
Maximum photovoltaic input power 5KW
Two AC outputs Yes
Maximum one-way AC output power 3.6KVA (Universal Gauge AC Output*2)
Maximum two-channel AC output power 3.6KVA / 3.6KW (Ground Wire)
Maximum AC total output power 3.6KVA / 3.6KW
Parallel machine function NO
Lithium-ion communication NO
Lithium battery activation Yes (photovoltaic or mains)
Input
Rated voltage 230VAC
Voltage range 170-280VAC (computer application); 90-280VAC (household appliances)
Frequency 50 / 60 Hz (automatic detection)
Output
Rated voltage 220/230VAC±5%
Instantaneous power 5400VA
Frequency 50/60 Hz
Output waveform Pure sine wave
Switching time 10ms (computer application); 20ms (household appliances)
Peak efficiency (PV to INV) 96%
Peak power (Battery to INV) 93%
Overpower protection 5s@>=140% load; 10s@100%-140% load
Peak coefficient 3:1
Power factor 0.8~1 (capacitive or inductive)
PV Charging & AC Charging
Charge mode MPPT
Maximum photovoltaic input power 5000W
Maximum photovoltaic open circuit voltage 500VDC
MPPT voltage range 40VDC~450VDC
Maximum photovoltaic input current 18A
Maximum photovoltaic charging current 100A
Maximum mains charging current 100A
Maximum charging current 100A
Battery Parameters BAT 256300 Remarks
Nominal Capacity 300AH 0.5C charging, 1C discharging, 25 ℃
8S
Rated Voltage 25.6V
Discharge Cut-off Voltage 22V  
Charging Cut-off Voltage 29.2V  
Float charging voltage 27V  
Continuous charging maximum current 100A  
Maximum current for continuous discharge 150A  
Battery Energy 7680Wh  
Rated Output Power 3600W  
Communication Interface NO  
Discharge working temperature -15 ℃ – 50 ℃  
Charging working temperature 0 ℃ – 50 ℃  
Relative Humidity 5 ~ 90%  
Altitude ≤4000m  
Protection Grade IP21  
Storage Time Keep charging at least once every 3 months  
Number of cycles ≥6000 times 75% DOD 25℃
Main Parameters For BMS
Overcharge Protection Overcharge detection voltage Monomer 3.65 ± 0.06V
Overcharge protection delay 0.5S
Over Discharge Protection Overdischarge detection voltage Monomer 2.7 ± 0.05V
Overdischarge protection delay 0.5S
Overcurrent Protection Working Current 1.1%
Overcurrent Recovery Disconnect Load /
Self Consumption Power Working Current ≤10mA
Sleep Current ≤50uA
Physical Property
Product Size, length x width x height (mm) 740*400*240
Package Size, length x width x height (mm) 775*473*420
Net Weight (Kgs) 65.75
Gross Weight (Kgs) 77.75
LCD Yes
Application Environment
Operating temperature range -10°C to 55°C
Storage temperature range -15°C – 60°C
Humidity 5% to 95% relative humidity (no frost)

Product Appearance Requirements

The edge sealing tape of the battery pack must be neatly applied and free of bubbles;
The position of the anti vibration sponge attached to the outside of the battery pack is regular and neat;
Clean appearance of battery pack;

Packing, Shipping & Storage Requirements

Product outer packaging box packaging requirements:
comply with the requirements of the product packaging schematic diagram.
Product transportation requirements:
1.During transportation, batteries should be protected from severe vibration, impact, or compression, as well as
exposure to sunlight and rain. They can be transported by vehicles such as cars, trains, ships, and airplanes;
2.During the loading and unloading process, batteries should be placed gently to prevent falling, rolling, and
heavy pressure. Product storage requirements: 1.The battery should be stored indoors in a clean, dry, and
ventilated environment with an ambient temperature of -10 ℃ to 35 ℃ and a relative humidity of no more than
85%; 2. The battery should be kept away from corrosive substances and kept away from sources of fire and heat;
3. Battery storage SOC: 40% to 60%.

Scroll to Top